Type Of Landfill

1. Mountain Qi buried landfill

This kind of landfill uses natural gullies and valleys to make harmless urban solid waste. Generally, the height difference of such landfills is relatively large, and the geology is between dilution and permeability. Therefore, the splitting and guiding of rainwater and the setting of the seepage control system are the key to enabling this type of landfill.

2. Beach landfill landfill

This kind of landfill is mainly located near the beach and has been deposited by long-term impact. Its bottom elevation is lower than the normal ground and the bottom is closer to the water table. When this type of landfill is activated for waste sorting plant factory, the artificial anti-seepage dam will be built in the planned landfill area. The key point is the setting of the groundwater seepage control system.

3. Plain landfill type Aochang

This type of landfill is generally suitable for areas with flat terrain and shallow groundwater burial. Generally, the garbage sorting equipment is used to bury the garbage. When determining the landfill height above the ground level, the slope ratio of the operation must be fully considered, usually 1:4. The area at the top of the landfill can ensure the garbage truck and The push compaction machinery is used for safe work on it. Since the shortage of search sources has become a prominent problem in landfill operations, excavation of foundation pits at the bottom of landfills is an effective way to ensure the availability of landfill cover materials.

Five Points To Cool Down The Waste Sorting Equipment In Summer

1. Clean the oil and dust of the motor body in time to ensure that the motor maintains good heat dissipation.

2. Care should be taken to maintain and maintain the equipment of the waste sorting equipment. Regularly check the equipment, do a good job of equipment maintenance, replace the oil regularly, replace or adjust the belt, and check whether the components are working properly.

3, for the equipment working outdoors, you can properly build some sunscreen nets or tents, etc., to help the equipment block the sun, because prolonged exposure, it will easily lead to equipment aging, and sometimes high temperature will cause the equipment to work properly , affecting the quality of work and efficiency of the equipment.

4. The installation environment of the equipment in the room is preferably set in a place with good ventilation. At the same time, it is necessary to adjust the indoor temperature and the ventilation and air permeability of the surrounding environment. It is best to ensure that the working environment temperature does not exceed 40 degrees, to maintain a good working environment for the waste sorting machine.

5. For some core components of the equipment, check the temperature at any time during the work. If the temperature is too high, be sure to stop and rest, or take some measures to reduce the temperature of the parts. Because too high a temperature can easily lead to aging of the equipment and shorten the service life.

The Most Effective Way To Recycle Useful Ingredients In Garbage Sorting

Nowadays, there are many new terms, such as garbage compression, plastic waste sorting machine, etc. Many people say that garbage can also be recycled? In fact, some garbage can be recycled, otherwise the trash can will not be divided into recyclable and non-recyclable garbage. Today, the garbage compression station company will take you to the most effective way to know the recycling of useful ingredients in the garbage. From the situation of domestic waste classification survey, the content characteristics of each component are as follows: the content of various available waste paper, metal, plastic (including beverage bottles, etc.), leather, etc. is the remaining after the health care workers have been roughed once. If the substances available in the current domestic garbage are further classified and recycled through waste sorting equipment China, the amount of waste will be directly reduced by 25.74%, and the humus will be used (main components: leaves, weeds, vegetable leaves, fruit peels, discarded foods). Etc.) Collective collection and centralized treatment can not only become a good fertilizer, but also reduce the weight of domestic waste by about 50%. From this point of view, it is feasible to reduce the amount of domestic waste. With the improvement of the living standards of urban residents, the changes in the fuel structure of residents, and the improvement of the way of living fuel, petroleum liquefied petroleum gas, gas and natural gas will gradually replace coal, and the amount of ash will drop sharply, which will produce significant reductions in waste effect.

Future Trends Of Hydraulic Baler Machine

With the continuous development of science and technology, the degree of mechanical automation is gradually increasing. Waste paper hydraulic balers are also included. There will be a lot of waste paper in our lives and offices. Hydraulic baler machine is suitable for all kinds of waste paperboard, waste paper box, waste paper shell, waste paper barrel, waste paper edge, waste plastic and other waste garbage packaging, to achieve cost saving and convenient transportation.

paper baler machine are divided into automatic and semi-automatic equipment. The function is to increase profit margin, reduce labor and improve work efficiency for the practitioners. The production line consists of main engine, conveyor, hopper and air cooling system. The equipment has stable performance, high cost performance, simple operation and good safety performance.

The fully automatic waste hydraulic paper baler provides more convenience for people's living environment. It is believed that more enterprises and individuals will choose automatic waste paper balers. I believe that the future balers will be better balers. The future development of waste paper hydraulic balers will also be bright!

Usage Precautions Of Waste Recycling Equipment

1. Special attention must be paid to the special voltage and capacity for this machine only.

2. The ground terminal must be connected to the ground.

3. Waste recycling equipment, the length of the cross section of the extended cord is 0.75mm2 or more and 10m or less.

4. Always use gloves, protective glasses, and a mask when installing or packaging.

5. This machine is a baler that uses a strap on the packaged object. Do not use for other purposes. Packaged items are items that need to be packaged. Do not put your hand or body close to the subject

6. Do not remove parts such as panels, covers, doors, etc. when using the machine. When the parts are removed, not only will the machine malfunction, but it will easily lead to ginseng accidents.

7. Do not modify the machine.

8. Waste recycling system, do not place the power cord in a channel such as a forklift, or avoid direct pressure on the power cord. Once the skin is damaged, broken, etc., it is dangerous.

9. Packing water or wet items, there is a risk of electric shock.

10. When not in use, the plug on the socket must be unplugged.

11. When the heating plate is at a very high temperature, do not put flammable materials around the back of the machine, which is a fire hazard.

Reason Of Waste Sorting Equipment Supplier Is Booming

We all know that rural areas have vigorously developed straw biogas in recent years, and the scale of the straw biogas industry is growing. So what is the source of the development of waste sorting equipment China? What is the reason for the scale of the straw biogas industry to become bigger and bigger?

 Secondly, the larger the scale of the waste sorting equipment supplier, the more substances that can be used comprehensively, and the better the benefits.

In the past, most of the rural areas used crop stalks as water for cooking, cooking and heating. This method can be used in low raw and unsanitary conditions, and it will also bring environmental pollution. Now farmers in some areas are simply in the original The ground is a torch. It not only wastes energy, pollutes the environment, but sometimes causes serious traffic hazards.

In response to this phenomenon, under the guidance of the principle of “reduction of the world and reuse”, the state and the government have continuously increased their efforts in policy support, financial support and technology investment, and successively introduced a series of policies to promote and develop circular economy. To consider the economic, environmental and social benefits of the orange stalk biogas industry.

Common Failures And Solutions Of Waste Compression Machine

Failure phenomenon: the waste compression machine is normally opened, and the compression packaging process does not automatically stop, and is infinite compression.

Solution: check to see if the limit switch is working properly. If other components are fault-free, it is likely that the limit sensor is in trouble. From left to right are power switch, potentiometer and reset button. If the push head does not stop, and other circuits have no problems, most of them are caused by sensor failure.

Debug the method, detect whether the sensor is sensitive, and then fine - tune. If the thruster of waste compression system works normally within a certain range, it is definitely a sensor fault.

Precise control potentiometer is recommended.

1. Remove the small screw fixed on the black knob with a small screwdriver and remove the black knob.

2. Remove the fixing screw and remove the potentiometer from the inner side. It can be seen that the potentiometer has three outgoing positions, two of which are connected to the computer board and the other one is broken.

Remember to remove the potentiometer with a soldering iron. Then replace the new potentiometer.

Operation Procedure For Hydraulic Baler Machine

1. The material of the hydraulic baler machine must be a hydraulically packed rack rod with defects such as deformation and cracks. The connecting parts and fasteners are strictly forbidden. The fasteners of the hydraulic baler and the connecting parts must not be welded. Way to fix.

2. The foundation of the hydraulic baler must be flat, compact and hard. The metal substrate must be flat and must not be deformed. When the ground is soft, the sweeping rod or pad must be used to increase the force surface and increase the stability.

3. All baler machine must be erected according to relevant standards and regulations (hydraulic balers should be horizontal and vertical, span and spacing should meet the requirements of the specification). No instability is allowed regardless of the height to which the hydraulic baler is placed.

4. The springboard on the hydraulic baler must be laid neatly, the width and length should be consistent (except for special parts). The springboard on any hydraulic baler must be fixed firmly and there must be no large holes on the platform surface (except for special parts).

Things About Waste Compression Machine

A lot of waste solution equipment manufacturer production machine of the significance of understanding is one-sided, wastepaper baling press enterprise can not completely no matter enough to their own interests, and thus damage the wastepaper baling press industry a good environment. Waste paper charter companies are members of a society, and their survival cannot and should not be based on social rejection. So in today's society of the trend of The Times, the behavior of the waste compression machine is not and can not be simply a reflection of their own purpose, and will give a negative impact on the environment of the whole society.

Waste compression machine solves the following technical problems:

(1) the binding wire is not cut completely

(2) uneven feeding leads to automatic binding stop

(3) incomplete package blocks will not produce complete package blocks in case of insufficient materials.

(4) the size and weight of each bag are different.

(5) too much feeding, and the feeding cylinder cannot reach the cylinder stroke

(6) the inaccuracy of the compression disc of the compressed oil cylinder leads to the problem of filling leakage blocking the compression chamber

Features:

Automatic control mode, safety interlock switch

Independently install the emergency stop button, which can be shut down at any time in any state to ensure waste compression system safety;

Guide groove balance is adopted to prevent tilting effectively.

Hook type automatic bag turning, safe and convenient;

Fast lock and release device, safe and efficient;

Nine Using Characteristics Of Plastic Baler Machine

1, No deformation and short circuit characteristics, packaging for a wide range of applications.

2. The whole machine combination is perfect and mature, with low noise and reduced work pressure.

3. Any packing belt in the market, and from 6mm to 15mm, the best bonding effect.

4. Plastic baler machine has a high countertop and is easy to operate. It is suitable for packing lighter items.

5, the standby state of the stop within 60 seconds after the completion of the baling action, a new generation of electric steel sheet design.

6. The machine adopts a new integrated circuit, and the access PC board controls the entire packaging action subwoofer design.

7. The machine is a mechanical structure, some of which are imported parts, the blade is stable and reliable, and the adjustment is convenient.

8, improve the design, elaborate manufacturing, a wide range of use, regardless of size packaging, you can pack without adjusting the baler machine.

9, the bale speed is fast, each bundle only takes 2.0 seconds. Instant heating, the heating piece can be operated within 5 seconds, enter the optimal packing state, save electricity and practical.

It's important to make sure that garbage is sorted properly

It's important to make sure that garbage is sorted properly. In many cases, people put recyclable things in the trash. Some of these items can be very valuable. If you're seeking a garbage sorting system, you'll want to actually get the best system which is available to you.

Locating A System That Fits Your Needs

You will find all kinds of waste recycling systems that sort and separate garbage. If you're attempting to choose the best system to suit your needs, you'll have to take into account your requirements. Take into consideration what you should be employing your computer for. Aim to find a system that works with your requirements.

Don't imagine that any system is wonderful for you. You must look closely at every option that you have. Take into consideration if the systems you're considering would be right for you. Take the time to find the kind of system that can handle everything you need it to accomplish.

Choosing A System That Had Been Made By A Reliable Manufacturer

You have to be sure you can depend on the system that you simply choose. If you're looking for a reliable system, you need to specifically search for a thing that was made from a well-established and trustworthy manufacturer.

Once you know that you can trust the company that made your garbage sorting system, you won't have to bother about your computer in the foreseeable future. You'll be able to concentrate on features and also other details. You'll understand that you're getting a high-quality system.

Looking For A Garbage Sorting System You Could Afford

It's a wise idea to set an affordable budget when you're purchasing this kind of equipment. A system this way may cost a large amount of money. In case you have a good budget set up, you could make sure you don't spend anymore than you must. You'll have much more control over your spending.

Setting a financial budget will even enable you to use price filters. You'll find the most effective systems that are within your budget range. You'll be impressed when you see just how much you can save.

There are a lot of great automated waste segregation systems on the market right now. If you are planning being buying one of these simple systems, you'll desire to pick a garbage sorting machine manufacturer that offers all of the things you're trying to find. Make certain you'll be delighted with the system you buy.