Precautions for Installing Industrial Waste Baler

 1. The quality of the oil pump device has a very important impact on the smooth operation and service life of the pump, so the device proofreading operation must be carried out carefully and must not be rash. The support or base of the hydraulic pump of the industrial waste baler must be strong and strong, and the pump shaft of the hydraulic pump must be aligned with the motor.

2. The position, length and pipe diameter of the suction pipe of the oil pump should reach the accounting value, and strive to be simple; and let the pump not be larger than the cavitation margin during operation. The inner diameter of the suction pipe must not be less than the requirements of the rule. The suction pipe should not be too long. The bend at 90 degrees should not be more than two. It should be connected to the oil pump with a soft short connection.

3. The suction and discharge lines of the oil pump should have brackets.

4. The address of the installation oil pump should be spacious to facilitate maintenance work.

Hydraulic Cardboard Baling Machine China

Check the temperature and vibration of the bearings during the test run after the hydraulic oil pump device of the hydraulic cardboard baling machine china. After loosening the coupling, use a spirit level to place it on the pump shaft and base of the electric oil pump. Adjust the wedge pads, check the level of the unit, and tighten the anchor bolts appropriately to avoid loosening. In order to prevent impurities in the pipeline from entering the pump, a filter should be installed in the pump glue for the pipeline of the new device, and its useful section should be 2 to 3 times the section of the suction pipe.

There are many types of packing belts on the market, and the quality is also uneven. So what are the characteristics of industrial waste packing machines and what occasions can they be used for? It may be difficult for users who have never used packing belts. Relevant characteristics of the strap material of the auto tie baler machine.

1. Small elongation: The elongation is one-sixth that of polypropylene (PP) tape, which can maintain the tension for a long time.

2, beautiful and not rusty: no steel belt rust pollution pollution objects, the color is bright.

3, strong temperature resistance: melting point is 260 degrees, no deformation below 120 degrees.

4, strong tensile strength: not only the tensile strength of steel belt, but also the resistance to impact ductility, can ensure the safety of your product transportation.

5. Good economic benefits: The length of 1 ton plastic steel belt is equivalent to 6 ton steel belt. The unit price per meter is lower than steel belt, which can save you costs.

6, good flexibility: sharp edges without steel belt, safe operation, neither hurt your hands nor damage the bundled objects.

Baler Troubleshooting

 Because the packing machine is simple and convenient to operate, easy to use and highly effective, it is the reason why most companies choose the packing machine. There are many problems with the packing machine. When there is another failure, how should we solve it? Today, I will briefly introduce the problems and solutions of the baler today:

How to solve the problem of the poor bonding effect of the packing belt:

1. The temperature adjustment knob is not adjusted properly.

In the electrical appliance control box of the baler, above the circuit board, open the control box cover, you can clearly see an adjustment knob, turn it clockwise to increase the temperature, and vice versa. If the temperature is too high or too low, the bonding effect is not good, so do not adjust it too much at one time, generally it can be adjusted between 4-5.

2. The power supply voltage is abnormal.

This machine should use 220V voltage. In many factories, the voltage is often insufficient. If long cables are used again, the voltage will drop, the soup temperature will be lowered, and the motor will even be burned when it is tightly tied.

3. The pull spring of the electric heating monster fails.

The long tension spring on the electric monster is tired. In this way, the inability to send the hot head between the two upper and lower straps results in half or even less adhesion.

4. Improper adjustment of the position of the ironing head of the baler.

The hot head is too high or too low, or left or right, it can't heat the upper and lower two layers of packing belt when it collides with the packing belt or the cutter. It should be adjusted according to circumstances.

5. The middle knife bearing is broken.

The middle knife bearing is broken, so it cannot be pushed up, and the packing strap is pressed to make it stick.

6. The temperature inside the machine is too high.

Failure of the exhaust micro fan caused the temperature inside the packer to be too high.

7. The heat-resistant wire of the iron is faulty.

Check whether the heat-resistant wire is broken or burnt. If the nut is loose, tighten it.

8. The tightening force of the baler is adjusted too much. Properly adjust the tightening force.

Aging problems of automatic balers:

The maintenance condition of the horizontal baler machine often determines the service life of the machine itself and the operating efficiency of the machine. The automatic baler itself is actually classified as a high-precision machine. The high-precision machine's process requirements are: Very high, its structural parts must be strictly inspected before they can be mass-produced. The internal irregularity will cause problems and defects in the automatic baler often. Secondly, it is a matter of moderation of its own use. Everything has a freight cost. The high intensity and overload of the operation make the service life of the automatic baler shorten. Moderate attention should be given.

The daily maintenance of the automatic baler is the basic work of equipment maintenance, and it must be institutionalized and standardized. Regarding the regular maintenance work of the fully automatic baler, work quota and material consumption quota shall be formulated and evaluated according to the quota. The regular maintenance work of the fully automatic baler shall be included in the assessment content of the worker contract responsibility system.

Horizontal Baler Machine

The regular inspection of the fully automatic baler is a planned preventive inspection. In addition to the human senses, the inspection method is also performed according to the regular inspection card. Regular inspection is also called regular inspection. Fully automatic baler equipment should also be thoroughly inspected and responded: inspection of oil cylinders, oil pumps, electrical appliances, and various sliding parts. The maintenance of the fully automatic baler should be carried out according to the maintenance procedures. Fully automatic packing machine maintenance regulations are requirements and regulations for the daily maintenance of equipment. Adherence to the implementation of full automatic packing machine maintenance regulations can extend the service life of the equipment and ensure a safe and comfortable working environment.

We are the garbage sorting system manufacturer, in the environment industry, we mainly engage in research, manufacturing and sales of hydraulic products such as waste transfer equipment and waste sorting equipment.

Process Flow of Fully Automatic Baler

For fully automatic balers, it can be applied to many industries. And this is mostly because of its unique way that many companies like it very much, especially the bulk materials industry. For the bulk materials industry, what they are most afraid of is product quality and safety. General packaging equipment cannot effectively guarantee the quality of loose materials. For the straw baler, its unique hydraulic packaging technology can completely achieve aseptic packaging.

The tape is delivered to the position → the binding signal is received → the brake is released, the main motor is started → the right ejector is raised, and the right belt is placed on the slide → the “T” guide is retracted → the proximity switch senses the ejection probe → the main motor stops, Brake pull-in → Packer unwinding belt motor rotates, withdrawing belt for 0.35 seconds → The belt is tightened and tied to the object → The main motor is started twice, the brake is pulled in → The large swing lever is pulled twice, the belt is tightened → the left acrosome is raised.

Tighten the lower layer of tape → the heating sheet extends into the middle of the two tapes → the middle ejector rises, cuts the tape → the middle ejector drops → the middle ejector rises again to make the two straps firmly adhered → the middle ejector falls, and the left and right ejectors descend simultaneously → Heater plate reset → Slide back → “T” -shaped guide plate reset → Proximity switch senses the tape-feeding probe → The tape-feeding motor starts and drives the tape to send the tape → Reset of the large swing bar → The tape is in place and the head is pushed to the “T” -shaped plate The proximity switch senses the double probe → the main motor stops, the brake pulls in → the packer completes a working cycle.

Safe use of fully automatic balers:

Automatic baler & sorting project china still needs human manipulation, monitoring and maintenance. Its operation is in a human-machine environment. From the perspective of safety, we must ensure the safety of people, machines and the environment It is necessary to coordinate human-machine relations to ensure system security. Therefore, in the process of using the automatic baler, pay attention to some safety matters.

The first thing to note is that before operating the baler, the operator must read the instruction manual in detail.

Automatic Tie Baler Machine

In real life, many people will ignore the role of operating instructions. Even if they consult others, they are unwilling to read the instructions in detail, so they ignore many issues that need attention, and even cause property and personal loss. It should be known that, under the requirements of national regulations, manufacturers will include issues that need attention in the operating instructions. Secondly, when operating the machine, the operator must not place the body parts in a space accessible by the rear folding cover to prevent accidents. Also, for safety, be sure to turn off the power and air supply when installing and removing the tape and during normal maintenance or repair. The last thing to say is untrained personnel. Please do not approach or touch the machine at will, and do not cause unnecessary injuries because of curiosity.

The use of an automatic tie baler machine should not only pay attention to the above, but also pay attention to the design of the mechanical working space. The working space of the packer should ensure that the operator has sufficient room for movement in accordance with psychological and physiological requirements; there should also be enough space and safe passages at dangerous work sites to avoid in unexpected situations.

How to Prevent Moisture from Entering the Automatic Baler Equipment During Operation?

(1) Water corrodes the metal in the hydraulic system of the auto tie baler machine, shortens the service life of the components, and the particles of the corrosion fall into the system, causing wear.

(2) (2) Accelerate the deterioration of oil, especially in the presence of particles such as iron, copper, manganese, etc., and the oxygen in the water and the air rapidly oxidizes the oil to form a viscous polymer, commonly known as sludge. When the use temperature exceeds 65 degrees, the oxidation speed will increase. For every 10 degrees, the oxidation will increase exponentially.

(3) Lubricity is reduced.

Due to the influence of moisture, the content of water in the automatic baler oil is stipulated. The general automatic baler system must not exceed 0.5%, and the requirements for more precise equipment will be higher. We have to keep the hydraulic oil under atmospheric pressure when using the machine.

Auto Tie Baler Machine

In addition, in order to reduce the influence of moisture, the fuel tank of the fully automatic baler should be capped as much as possible. Especially for outdoor machines, due to changes in air temperature, the ingress of rainwater should be avoided, and the system should use a hydraulic closed circuit system to minimize the impact of moisture.

The maintenance of recycling baler machine often determines the service life of the machine and the efficiency of the machine. The automatic baler itself is actually classified as a high-precision machine. High, its structural parts must be strictly inspected before it can be mass-produced. The internal irregularity will cause problems and defects in the automatic baler often.

Secondly, it is a matter of moderation of its own use. Everything has a freight cost. The high intensity and overload of the operation make the service life of the automatic baler shorten. Moderate attention should be given.

China mobile waste sorting machine supplier believes that the daily maintenance of automatic balers is the basic work of equipment maintenance and must be institutionalized and standardized. Regarding the regular maintenance work of the fully automatic baler, work quota and material consumption quota shall be formulated and evaluated according to the quota. The regular maintenance work of the fully automatic baler shall be included in the assessment content of the worker contract responsibility system.

The regular inspection of the fully automatic baler is a planned preventive inspection. In addition to the human senses, the inspection method is also performed according to the regular inspection card. Regular inspection is also called regular inspection. Fully automatic baler equipment should also be thoroughly inspected and responded: inspection of oil cylinders, oil pumps, electrical appliances, and various sliding parts. The maintenance of the fully automatic baler should be carried out according to the maintenance procedures. Fully automatic packing machine maintenance regulations are requirements and regulations for the daily maintenance of equipment. Adherence to the implementation of full automatic packing machine maintenance regulations can extend the service life of the equipment and ensure a safe and comfortable working environment.

The Maintenance And Maintenance Work Of The Hydraulic Packer

 First, its maintenance work is introduced in detail. hydraulic cardboard baling machine china works to remove debris or dirt for maintenance from one week to 10 days.

Second, one month after the hydraulic baler works normally, the cleaning, maintenance and lubrication of the upper slide, middle knife and front ejector described in the previous paragraph will be performed once. The third is to perform all maintenance on the shaft (heart) and bearings every three months, except for the above two maintenances.

The hydraulic packer replenishes the oil in the gearbox of the reducer every two years. Also note that several parts cannot be refueled: rollers and reels, all belts, sliders and surrounding.

Cards may appear when the hydraulic packer is working properly. For example, how to handle horizontal waste paper hydraulic balers? Below, Belik teaches you how to deal with it. The horizontal waste paper packing tape is stuck in the center of the roller, or there is a foreign matter blocking the box. Loosen the countersunk head screws on the central connecting shaft, remove the connecting shaft, pick up the upper turbine, and remove the stuck object.

Hydraulic packers cannot form a belt without proper wear. Hydraulic packer equipment has been in use for a long time and has not been cleaned and maintained in a timely manner. As a result, swags are present in the machine, which makes the belt non-smooth and does not form. Using a belt, the horizontal waste paper baler can be completely cleaned and returned to normal.

Some hydraulic balers sometimes have problems, such as not actively feeding the belt. First check whether the potentiometer for belt length control is at the zero position. The potentiometer for belt length control is located at the left side of the front panel switch card. If it is at the zero position, it will not be performed.

China sorting machine MSW supplier believes that hydraulic balers have advantages and disadvantages in both vertical and horizontal styles.

The hydraulic packer has a horizontal packer and a vertical packer. The hydraulic packer is simple and complete, which can increase the total power of the packaging and save the labor cost of packaging. The hydraulic packer lead frame consists of four sets of wire equipment installed on the frame. The entire lead frame is suspended on the central axis of the press frame and moves horizontally relative to the press frame under the action of a hydraulic motor. The frame is a welded part with wheels at the bottom and moves horizontally along the main track as the hydraulic cylinder advances. Hydraulic balers are usually used to receive and manipulate compressed cardboard, waste film, waste paper, foam plastics, beverage cans and industrial decoration. With the advancement of technology, industrial development and the use of balers. Therefore, the baler has also been recognized by more and more people. It is used more and more widely.

Waste Recycling Equipment Factory

Hydraulic baler and horizontal waste paper hydraulic baler. As a result, this results in higher vertical packaging costs and lower power. The atmosphere of the hydraulic packer in the oil mixture or in the hydraulic cylinder is not completely exhausted. The hydraulic packer produces a cavitation phenomenon under the high pressure effect and generates a large noise. Whether it is a horizontal baler or a vertical baler, it has its own advantages and disadvantages, such as the low cost of a vertical baler, a small footprint, the high cost of a horizontal baler, and a large footprint.

The hydraulic packer is used to squeeze waste paper and similar products under normal conditions and is packed with special packaging tape to reduce volume, thereby reducing transportation volume, saving freight and increasing corporate profits. purpose. However, some operators and controllers are more casual, especially in the hot summer, especially when they work barefoot everywhere, but this is very dangerous, not only because the debris on the ground straps can stab feet, but more importantly if The floor is wet and easy to connect. Lead to very serious consequences.

Second, the wire connector is not fixed. In the production hall, the equipment is sometimes far from the power source, or the original wires are not long enough. At this point, the wires are connected, but the operator saves the connected wires directly to save time. Driving on the ground without following the direction of the wiring duct is very dangerous. The working conditions of waste paper balers are usually not very good, and all minor safety issues are easily overlooked, causing unnecessary losses.

Teach You How to Buy a Waste Paper Baler

Waste sorting system China supplier introduces you: Waste paper packing machine is a kind of packing machine that does not require manual feeding, and is completely packed by the machine itself. The price of automatic balers in the market only provides consumers with needs, but when choosing a baler, it should be noted that balers are divided into automatic balers and semi-automatic balers, so there are some things to consider when choosing the price of a baler. And choose automatic baler. Let me explain a few points about choosing a fully automatic baler.

1. High standard automatic packer is suitable for carton packing in hardware, food and other industries.

2. Low standard automatic packer has a low table, you need to get the package manually to pass the packaging equipment. The tabletop is high enough to be customized to the customer's conveyor line.

3, side standard automatic packing belt Because you do not need to worry about the body's dust, water droplets and corrosive liquid erosion and abrasion, this automatic packing machine can be used to pack cartons with liquid, seafood and dust.

4. Because it can be used alone and with the assembly line, this one is mainly used in post and telecommunications, chemical, home appliances and other industries.

5. From this perspective, customers can't see the surface price when choosing automatic balers and semi-automatic balers. It is bringing the product to the field application so that you can better select the good product and still have a look. The actual situation of the manufacturer.

Paper Baler Machine

The electromagnet of the waste paper baler does not work properly. The solenoid does not work. First check whether the solder joint is broken, and then check whether the coil is burned out. If there are no abnormalities, check whether the electromagnet is dislocated or blocked by the stolen material to prevent the bullet from moving freely. The temperature of the horizontal waste paper packaging machine and heater can be suspended by the internal temperature scheduler. Generally, the good size of the method is "4". The entire consuming process is not heating, doping or other processes, but direct cold forming. Forming together also ensures the same raw material. For example, cast iron chips are used instead of cast iron after forming. For castings using special materials, recycling is even more important.

The advantages of a paper baler machine in packaging waste paper boxes are basically manual packaging with a rope, but a waste paper baler can quickly improve work efficiency. The protection of waste paper balers is widely used in the industrial production industry. . With the continuous development of society, the requirements for packaging are constantly increasing, the technology is constantly improving, and it is becoming more and more intelligent. Therefore, the improvement of industrial efficiency is also obvious, so the waste paper packing machine manufacturer has brought a lot of changes in industrial progress.

Waste Paper Baler Can Handle Many Types Of Books And Is Widely Used

Waste sorting equipment manufacturer share with you:

Paper baler machine has good toughness, good stability, beautiful appearance, convenient operation and maintenance, safety and energy saving, and low investment cost for equipment and infrastructure engineering. It is widely used in various waste paper mills, used materials recycling companies and other unit enterprises. It is suitable for packaging and recycling used waste paper and plastic straws.

It is a good equipment to improve labor efficiency, reduce labor intensity, save manpower, and reduce transportation costs. Waste paper baler is an electromechanical integrated product, which is mainly composed of mechanical system, control system, feeding system and power system.

The waste paper baler can be classified according to the following standards:

1. Manual baler: Generally, manual operation is required to complete the entire process. In general: electric heating, iron buckle clamping.

2. Semi-automatic packing machine: After the packing machine is manually inserted into the packing tape, the machine will automatically complete the process of packing, gluing, cutting and removing the packing tape, because each product requires manual operation.

 Waste Paper Baler

3. Fully automatic baler: There is no need to manually insert the belt, and its triggering method is divided into a little movement, manual, continuous playing, ball switch, foot switch, and the packing can be automatically completed by simply pressing the switch, which is convenient and quick.

What kind of books can waste paper baler handle? The following introduces you:

1. Used books: second-hand books, no matter how used.

2. White paper: pure white, clean, no film.

3. Binding paper edge: Cut the paper edge when printing books, with a small amount of copper plate and plastic head.

4. Yellow board: The discarded boxes are mainly yellow.

5. Gray card: gray from outside to inside, no film, can bring color.

6. New newspapers: too many unused newspapers.

7. Old newspapers: used newspapers obtained from waste paper collection stations.

Newsprint: same as newspaper paper, but without color words.

Newsprint: same as newspaper paper, but without color words.

Paper cup: and the remaining paper in the production of paper cup.

Tetra pak packaging: such as milk cartons.

11. Pages: the paper is messy, no glue, no film, you can have text.